Structural Fire Damage Cleaning in Riverview, FL
The drywall is gone, and now you are staring at blackened studs, scorched joists and a charred roof deck. Somebody now has to decide what gets blasted clean, what gets sistered and what gets replaced. Unify Fire Solutions connects you with independent, licensed and insured contractors in Riverview who clean the framing, masonry and steel itself.
- Soda, dry ice and hand cleaning of framing
- Every stud and joist probed for char depth
- Sealer applied to lock in residual odor
What Makes Framing Work Different
Hang new drywall over sooty, smoky studs and the smell comes back through the paint on the first warm day. This stage decides whether your rebuilt rooms smell fresh or smell burned for years.
Licensed & Insured Independent Pros
The contractors we connect you with are independent businesses carrying their own license and insurance. Verify both, and ask whether the crew follows the IICRC S700 standard for fire and smoke work.
Upfront Written Estimates
Media blasting depends on square footage, the media used and how hard the space is to get into. Get a written, itemized estimate in hand before any blasting begins.
Rapid Local Dispatch
A real person answers around the clock, and the search for a crew begins on that call. Timing depends on which crews near Riverview are free, and it is often the same day.
Blasting Rigs and Probing Tools
This trade runs on gear most remodelers do not own: soda blast pots, dry ice blasters, tow-behind compressors, HEPA vacuums, air scrubbers and an awl for probing char.
Do not climb into a burned attic or walk a scorched roof deck to look for yourself. Weakened joists and burned-through sheathing can give way without warning, and exposed wiring may still be live. Wait for the contractor to check that the structure is safe, and keep people off floors that sit over a burned crawlspace or basement.
Cleaning the Building From the Roof Deck Down
This is not contents cleaning and it is not debris haul-out. It is the work done on the wood, block, brick and steel that hold your house up.
Char Depth Probing and Member Decisions
An awl pushed into a charred stud tells the story: if it stops in sound wood after a thin layer of char, the member is usually a cleaning candidate. Deep char that eats into the section of a joist or truss chord means sistering or replacement.
- Members marked clean, sister or replace
- Structural engineer called in for questionable beams, trusses and headers
- Photos of each marked member for the claim
Soda Blasting
Sodium bicarbonate is softer than wood, so it strips soot and light char off studs, joists and roof decking without gouging the grain. Expect fine dust and residue that has to be contained and HEPA vacuumed when the blasting is done.
Dry Ice Blasting
With dry ice the pellets sublimate on impact, so there is nothing left on the floor but the soot itself. It suits cramped attics and areas around wiring, but it runs louder and pricier than soda.
- Hearing protection and ventilation required
- Good choice when residue would be a problem
Wire Brushing and Sanding
For a few blackened studs or a small closet fire, wire brushes, sanding discs and a HEPA-shrouded grinder may be all it takes. It is slow on big areas but precise where blasting would be overkill.
Brick, Block, Concrete and Steel Beams
Porous brick, block and concrete trap soot deep in the surface, so crews use alkaline detergents, scrub brushes or blast media to lift it. Steel beams and columns are cleaned of soot and checked for warping or sag, which goes to the engineer.
Encapsulation and Attic Insulation Removal
Even well-blasted wood can hold faint odor in its pores, so crews roll or spray a pigmented shellac-based or specialty encapsulating sealer over cleaned framing. In the attic, smoke-soaked blown-in or batt insulation is vacuumed out with a high-powered insulation vac before the rafters and decking are cleaned.
Under the house, the crew probes the joists, sill plates and subfloor underside, then blasts and seals what can stay. A smoke-stained or wet vapor barrier usually comes out and goes back new.
Ask your contractor which method they recommend for each area and why. It is common to see soda in open walls, dry ice in the attic and hand sanding near the electrical panel on the same job.
Containment matters here, since blast media and loosened soot travel anywhere the air moves. The crew hangs poly over doorways, masks off the HVAC returns and runs air scrubbers under negative pressure while they work. Ask how they will protect finished rooms and windows that were not damaged.
Looking at Blackened Studs and Rafters?
Phone our dispatchers and they begin searching for a structural crew close to Riverview. It costs nothing to call.
Call +1-833-336-1630How a Structural Cleaning Job Unfolds
- 1
Phone the Dispatcher
Describe what is exposed: open stud walls, an attic, a crawlspace, block or steel. Let us know if an adjuster, engineer or roofer has already visited.
- 2
Mobile Crew on Site
An independent crew shows up with its compressor, blast gear, poly and air scrubbers. They check that the roof and floor are safe to walk and that power to the open walls is off.
- 3
Probe, Mark and Quote
Every exposed member gets probed with an awl and marked clean, sister or replace, and anything borderline goes to a structural engineer. You get a written, line-item quote listing square footage, method, sealer and insulation removal before any work starts.
- 4
Blasting, Sealing and Walkthrough
After blasting and HEPA cleanup, the framing gets its sealer coat, and you walk the bare structure with the crew lead. Smell the space on a warm day and get photos of each tagged member before anyone hangs drywall.
What Callers Said About Their Structural Crew
After the attic fire, the rafters were black and the blown-in insulation was a wet mess. They vacuumed out the insulation, dry iced the rafters around the wiring and sealed it all. Two rafters were cut deep enough that they called in an engineer, and those got sistered.
My contractor brother-in-law said all the black studs had to go. The crew lead pushed an awl into each one and showed me the wood was solid under a thin crust. They soda blasted and sealed them, and only three were swapped.
The fire in our lower level left the block walls and the steel beam coated in soot. They scrubbed and blasted the block, cleaned the beam and had the engineer confirm it had not sagged. No smell now, even with the windows shut.
Your Structural Fire Cleaning Questions Answered
How do crews decide if a charred stud can stay?
The test is simple: they probe it. An awl or screwdriver pushed into the black surface shows how deep the char goes, and wood that is firm just under a thin crust can usually be blasted and sealed. Deep char, cracks or a reduced cross section mean sistering or replacement, with a structural engineer making the call on anything questionable.
What is the difference between soda blasting and dry ice blasting?
Soda blasting uses sodium bicarbonate media that is gentle on wood and helps neutralize odor, but it leaves dust and residue to clean up. Dry ice leaves no media behind and works well near wiring, but the equipment is noisy and the job usually costs more. It is common to see both on one job.
Why seal the framing if it has already been cleaned?
Smoke gets deep into the pores of the wood, past what blast media can reach. An encapsulating sealer traps what is left so the odor does not seep back through the finished walls. Sealer only works over clean framing, never as a shortcut over soot.
Does the attic insulation have to come out after a fire?
In most cases where smoke got into the attic, it does. Blown-in and batt insulation trap smoke and soot like a filter, and many get soaked by hose water too. It is vacuumed out with an insulation vac so the rafters and roof deck can be probed, blasted and sealed before anything new is blown in.
Can soot be cleaned off brick and concrete block?
Most of the time, but brick and block hold soot in their pores and need more than a wipe. Expect alkaline detergents and scrub brushes for light staining and media blasting for thick deposits. Heat-cracked or spalled block and brick should be looked at by an engineer or mason.
Do I need a structural engineer for fire-damaged framing?
You may not on a small job, but any doubtful load-bearing member calls for one. An engineer's report on trusses, headers, beams, steel and badly charred joists protects you and supports the claim. Your local building department may also require one before the walls close.
Structural Fire Cleaning Throughout Riverview
Calls come in from all over Riverview and nearby towns, from older homes with solid lumber framing to newer builds with engineered trusses and I-joists. Attics, basements, crawlspaces, garages and light commercial spaces all come up regularly.
- Attic fires
- Electrical fires
- Furnace puff-backs
- Chimney fires
- Lightning strikes
- Neighbor's fire spread
If the first crew we connect you with is not the right fit, call back and a dispatcher will connect you with another. Get the bones cleaned before anyone hangs new drywall.
